Table of contents for this article
It's the weekend, but I'm not going out......
Kawaguchiko Touring on a FridayThere was a flurry of phone calls and e-mails during the week, and it seems that if I don't get some work done over the weekend, next week will be tough, so I didn't go out this weekend.
I drove in the rain yesterday and washed my car while I was at work...... But it's very hot outside: ...... I'll start with what I can do in my room first.
SHOEI Z-7 How to remove the interior
I bought a SHOEI Z-7 TERMINUS last November, and it's the only helmet I've worn to the point where I'm worried about the lack of comfort around my cheeks and chin when I go out with my jet helmet....... I've never washed the interior ........
I wore it last night with a wet head, so the interior is moist. Before that, I was sweating and decided to wash the interior.
PDF of the instruction manual on SHOEI's websiteThe interior will be stripped off with a crunching motion while watching.
Easy. So, I soak it in hyter for a few minutes in the washroom and then wash it by hand. Finally, I finish up with Downy fabric softener and hang it out on the balcony.
After running in the rain. I'm curious: ..... I'm curious.
After working until late in the evening, I went down to the parking lot to clean off some of the rain stains from yesterday.......... No, it's pretty heavily stained: .....
There is a water supply in the parking lot, but it's a common property of the apartment building, and we can't just hook up a hose and use it without permission. The area around the rear fender is particularly bad.
I've been wondering about this since my Ninja 400 days, but this short rear fender is not doing its job ....... There's mud all over the rear suspension joint and deep into the swingarm......... I'm sure you can wash it with water and lubricate it.
Before I put in the OHLINS (I didn't say I'd put in the OHLINS), I thought I'd like to fix the problem, so I cleaned off the dirt from the car body with water from a plastic bottle.
I lightly lubricated the chain and finished today's outdoor work.
I think a slightly stickier one would be good for greasing the rear suspension mounting area........ What oil should I use? ......
Make the rear fender a little longer.
I guess I should try making the rear fender a little longer....... I've known this for a while. I've always known that I could make the rear fender a little longer, so I actually have this in my room at this point.
It was delivered when I got home on Friday.Puig rear inner fender。
I could have chosen the carbon one, but I chose the regular plastic one. Well, you can also try carbon cutting sheets at a later date.
Amazon says it's for the ER-6n, but it's a common part and should work on the Ninja 650/400.
The mesh on the side looks hard to clean, the design is a little too cool for me, and I don't want to ruin the original style, so I decided to forgo it this time, but if this Puig doesn't look long enough, I might try this next time.
It's a design that seems to be right in the middle of the Gundam generation.Odax's rear fender
gloves with holes
So I pulled myself up to my room, and the other thing I was wondering about was the mesh glove with the hole in it.
Summer gloves are made of mesh by Rough & Load.
I have long fingers, so the size was a little bit wrong. Only my left hand, where I frequently bend my fingers to shift gears, has a hole in the tip of my finger.
I'm pretty sure I bought this on Amazon.Rough & Load stores are within walking distanceI went for a walk and bought a pair of mesh gloves. I went for a walk and bought a pair of mesh gloves. They were on sale for 15% off.
And on my way home.Sun Tomato NoodlesI had a cold noodle soup and finished my Saturday.
The tomato ramen here is super delicious. Cheese topping recommended.
People who read this article also read
